(2020-10-17, 23:19)Gruff1973 Wrote: User Name for Forum : Gruff 1973
Station Number if you have one: None allocated, 3900-3D00-1551-3833-3036-3138
Region... (Europe, Asia, etc...) : europe, UK

Specify specific... don't enter a lot of comments... just the facts, please....
'station not listed': Not Listed
Forum operator status not upgraded,: Not Upgraded
Station Number NOT associated with my User ID...: yes, not associated

THanks for any help you can give

(2020-10-18, 21:29)Egon Wrote:

(2020-10-17, 23:19)Gruff1973 Wrote: User Name for Forum : Gruff 1973
Station Number if you have one: None allocated, 3900-3D00-1551-3833-3036-3138
Region... (Europe, Asia, etc...) : europe, UK

Specify specific... don't enter a lot of comments... just the facts, please....
'station not listed': Not Listed
Forum operator status not upgraded,: Not Upgraded
Station Number NOT associated with my User ID...: yes, not associated

THanks for any help you can give

If the Staton does not have a number, then it has not yet connected to the server on the Internet. The station must be connected to the Internet, otherwise it won't work. Since you were able to read out the processor ID, I assume that the station can be reached in the local network.

/Egon

So, the station is now up & running although I'm not 100% sure what fixed it!  THe only change that I made was to set the noted IP address of the controller to the IP that it had been handed out by DHCP, for some reason the address noted in the GUI was for another piece of kit on my home network - it may have been an IP clash perhaps...

In any case, it's working now & I'm delighted!  Much work to be done in dealing with interference and fine tuning the antenna positions now!

(2020-10-21, 18:59)SGJones Wrote: Hi, is this post still being monitored?

(2020-10-21, 21:17)dupreezd Wrote:

(2020-10-21, 18:59)SGJones Wrote: Hi, is this post still being monitored?

Your status is already changed to Participant.

(2020-10-31, 12:46)yVega Wrote: User name: yVega
User number: 2207
Station number: ?
Region: Europe

I'm online now, how can I get the associated station number?

(2020-10-31, 12:57)cutty Wrote:

(2020-10-31, 12:46)yVega Wrote: User name: yVega
User number: 2207
Station number: ?
Region: Europe

I'm online now, how can I get the associated station number?

Have you registered your station on the owner's page?  If in fact your station has sent signals to the server, it should be recognized, and on your controller page, upper right, should show a number, or instruction link to register.  under 'tracker' status, should show a server connection and address.... the system WILL not recognize you IF YOU HAVE NOT sent signals.  AND and the system WON'T become active at all unless good GPS is noted, and 1PPS signal syncs.

(2020-10-31, 13:00)cutty Wrote:

(2020-10-31, 12:57)cutty Wrote:

(2020-10-31, 12:46)yVega Wrote: User name: yVega
User number: 2207
Station number: ?
Region: Europe

I'm online now, how can I get the associated station number?

Have you registered your station on the owner's page?  If in fact your station has sent signals to the server, it should be recognized, and on your controller page, upper right, should show a number, or instruction link to register.  under 'tracker' status, should show a server connection and address.... the system WILL not recognize you IF YOU HAVE NOT sent signals.  AND and the system WON'T become active at all unless good GPS is noted, and 1PPS signal syncs.

(2020-10-31, 14:52)yVega Wrote: where I can read the Processor-ID for insert then in owner page?

(2020-10-31, 17:12)mwaters Wrote:

(2020-10-31, 14:52)yVega Wrote: where I can read the Processor-ID for insert then in owner page?

Please see https://forum.blitzortung.org/showthread.php?tid=2764&pid=20250&highlight=Processor-id#pid20250

(2020-10-31, 22:32)yVega Wrote:

(2020-10-31, 17:12)mwaters Wrote:

(2020-10-31, 14:52)yVega Wrote: where I can read the Processor-ID for insert then in owner page?

Please see https://forum.blitzortung.org/showthread.php?tid=2764&pid=20250&highlight=Processor-id#pid20250

Ok, thanks for your patient, it's all associated now.. tomorrow I'll position better primary antenna and gps antenna

(2020-10-31, 22:39)dupreezd Wrote:

(2020-10-31, 22:32)yVega Wrote:

(2020-10-31, 17:12)mwaters Wrote:

(2020-10-31, 14:52)yVega Wrote: where I can read the Processor-ID for insert then in owner page?

Please see https://forum.blitzortung.org/showthread.php?tid=2764&pid=20250&highlight=Processor-id#pid20250

Ok, thanks for your patient, it's all associated now.. tomorrow I'll position better primary antenna and gps antenna

yVega, what is your station number so we can have a look at it and move you to Participant status if you are sending signals.

(2020-10-31, 17:12)mwaters Wrote:

(2020-10-31, 14:52)yVega Wrote: where I can read the Processor-ID for insert then in owner page?

Please see https://forum.blitzortung.org/showthread.php?tid=2764&pid=20250&highlight=Processor-id#pid20250

(2020-11-03, 12:34)cutty Wrote:

(2020-10-31, 17:12)mwaters Wrote:

(2020-10-31, 14:52)yVega Wrote: where I can read the Processor-ID for insert then in owner page?

Please see https://forum.blitzortung.org/showthread.php?tid=2764&pid=20250&highlight=Processor-id#pid20250

You probably won't need to insert processor ID... unless you've taken over a station previously assigned to someone else,... if you have sent signals, and server has activated your station, the server knows it already, assuming it is associated with your user ID.  What you WILL have to do is input the correct antenna configuration, and, if you want its data displayed on maps, etc, make sure "ANON" is "NO"...