System Blue - Digital Filter Pin 1 Identification
#21
(2016-09-14, 20:30)kevinmcc Wrote:
(2016-09-14, 19:18)Polyphemus Wrote: Hello,

I added one filter IC for the E-amp channel, I soldered J0, but I don't see the extra filters menu... What am I doing wrong?

You may have to update the firmware.

Older versions did not have filter menu.

Hi Kevin,

Thank you for your reply. I am already on the latest beta firmware of System Blue, 8.1, but no luck yet.
Reply
#22
(2016-09-15, 07:00)Polyphemus Wrote:
(2016-09-14, 20:30)kevinmcc Wrote:
(2016-09-14, 19:18)Polyphemus Wrote: Hello,

I added one filter IC for the E-amp channel, I soldered J0, but I don't see the extra filters menu... What am I doing wrong?

You may have to update the firmware.

Older versions did not have filter menu.

Hi Kevin,

Thank you for your reply. I am already on the latest beta firmware of System Blue, 8.1, but no luck yet.


If you installed the filters correctly and jumped J0, you should be seeing the filter option for channels you have set to normal.

Maybe you can take picture of circuit board?
Kevin McCormick KB0UOI
Macomb, IL USA
Stations: 1539
Reply
#23
Do I have to solder IC's for all 4 channels? Currently I'm only using the E-amp, because I'm in the process of making my H-field antenna's. So I only soldered the IC for the E-amp... I disabled the H-amps in the config.
Reply
#24
No, there is an information somewhere in the manuals that you should start with one IC and then check if it was succesfully and if it helps.

I did not solder my 2 chips at the moment but I don't need more.
73 de Hartmut / DK5LH

Stations: 1582
Reply
#25
They can be mounted in random order and from one to four pieces.
The CPU tests J0, it is shorted, it sends clock signals, filter-ic or not Smile

/ Richo
Stations: 584, 585, 2017
Reply
#26
Here are some photo's of my setup, I do not see what I'm doing wrong  Huh

http://imgur.com/a/CXisS
Reply
#27
(2016-09-18, 13:19)Polyphemus Wrote: Here are some photo's of my setup, I do not see what I'm doing wrong  Huh

http://imgur.com/a/CXisS

Looks correct.

Could be jumper is bad, or a defect with the board.

RichoAnd what happens with the CPU connection is floating?
Kevin McCormick KB0UOI
Macomb, IL USA
Stations: 1539
Reply
#28
Hi everybody,

I have to apologize, the filter section is only visible when Remote Control mode is set Manual mode. I found it by accident... Sorry for the confusion...
Reply
#29
(2016-09-20, 14:57)Polyphemus Wrote: Hi everybody,

I have to apologize, the filter section is only visible when Remote Control mode is set Manual mode. I found it by accident... Sorry for the confusion...

I was just going to post that. Tongue

I was getting interference and testing automatic and noticed filters were gone.
Kevin McCormick KB0UOI
Macomb, IL USA
Stations: 1539
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Filter orientation - BLUE KY5G 2 15,326 2017-08-14, 05:03
Last Post: KY5G
  Digital lowpass filter radiofarol 3 21,221 2017-06-10, 22:23
Last Post: radiofarol

Forum Jump:


Users browsing this thread: 1 Guest(s)