Fault LED indicates fault
#1
I recently set up a System Blue.

The Fault LED is turned on. What does that indicate?


The controller indicates a GPS signal and Network (GPS led blinks, Network LED is turned on)

I wasn't able to find a description about how the LEDs should be interpreted. Is there such a description?
Reply
#2
Can you reach the web GUI?
Clément
Stations: 733, 1440, 2601
Reply
#3
The fault LED lights when the controller is in interference mode. Whether it lights under other conditions I do not know.
Stations: 1075, 1472
Reply
#4
(2016-06-30, 10:19)Andrew.Instone-Cowie Wrote: The fault LED lights when the controller is in interference mode. Whether it lights under other conditions I do not know.

Thanks.

I rearranged some cables and positioning of the antennas. The station is up running now.
Reply
#5
i have the same problem but it´s the alarm red is on all the time ??
Stations: 148, 1598, 1601
Reply
#6
(2016-09-13, 09:29)LennartJ Wrote: i have the same problem but it´s the alarm red is on all the time ??

What abput the other LED's?
What about the Web-GUI, can you read the system status on the browser?
Are you in "normal" mode or "interference"-mode?
73 de Hartmut / DK5LH

Stations: 1582
Reply
#7
(2016-09-14, 11:00)elythomaslumber Wrote:
(2016-09-13, 09:29)LennartJ Wrote: i have the same problem but it´s the alarm red is on all the time ??

the other LED's? they ar ok
What about the Web-GUI, can you read the system status on the browser, how do i do that?
no interference.
Stations: 614
Reply
#8
(2016-09-15, 09:41)Bergkvar Wrote:
(2016-09-14, 11:00)elythomaslumber Wrote:
(2016-09-13, 09:29)LennartJ Wrote: i have the same problem but it´s the alarm red is on all the time ??

the other LED's? they ar ok
What about the Web-GUI, can you read the system status on the browser, how do i do that?
no interference.

Aehmmm, you never did any configuration on the embedded web-server  of the system?

Maybe there is a misunderstanding...

- Check your router and find out what IP adress your System Blue got
- type in the IP adress in your browser
- you should see now the WEB-GUI and all information or configuration tabs
- see also here: http://de.blitzortung.org/cover_your_area.php?session=1  ; download the manual and read beginning of page 69
- maybe you did not disable AMP1 or AMP2 if there is no antenna connected to any of the input terminals?

Good luck!
73 de Hartmut / DK5LH

Stations: 1582
Reply
#9
(2016-09-15, 16:33)elythomaslumber Wrote:
(2016-09-15, 09:41)Bergkvar Wrote:
(2016-09-14, 11:00)elythomaslumber Wrote:
(2016-09-13, 09:29)LennartJ Wrote: i have the same problem but it´s the alarm red is on all the time ??

the other LED's? they ar ok
What about the Web-GUI, can you read the system status on the browser, how do i do that?
no interference.

Aehmmm, you never did any configuration on the embedded web-server  of the system?

Maybe there is a misunderstanding...

- Check your router and find out what IP adress your System Blue got
- type in the IP adress in your browser
- you should see now the WEB-GUI and all information or configuration tabs
- see also here: http://de.blitzortung.org/cover_your_area.php?session=1  ; download the manual and read beginning of page 69
- maybe you did not disable AMP1 or AMP2 if there is no antenna connected to any of the input terminals?

Good luck!

Thank i find it now its working fine now
Stations: 148, 1598, 1601
Reply
#10
(2016-09-16, 12:01)LennartJ Wrote:
(2016-09-15, 16:33)elythomaslumber Wrote:
(2016-09-15, 09:41)Bergkvar Wrote:
(2016-09-14, 11:00)elythomaslumber Wrote:
(2016-09-13, 09:29)LennartJ Wrote: i have the same problem but it´s the alarm red is on all the time ??

the other LED's? they ar ok
What about the Web-GUI, can you read the system status on the browser, how do i do that?
no interference.

Aehmmm, you never did any configuration on the embedded web-server  of the system?

Maybe there is a misunderstanding...

- Check your router and find out what IP adress your System Blue got
- type in the IP adress in your browser
- you should see now the WEB-GUI and all information or configuration tabs
- see also here: http://de.blitzortung.org/cover_your_area.php?session=1  ; download the manual and read beginning of page 69
- maybe you did not disable AMP1 or AMP2 if there is no antenna connected to any of the input terminals?

Good luck!

Thank i find it now its working fine now

I also have an error.
And no interface available.
Hardfault error
Please report
LR=8038f73
PC=80347d4

Firmware 8
After reset unit works.
Stations: 907
Reply
#11
(2016-09-19, 18:17)Arnaut.Stomphorst Wrote: I also have an error.
And no interface available.
Hardfault error
Please report
LR=8038f73
PC=80347d4

Firmware 8
After reset unit works.
Thanks for the info. This specific error shouldn't happen any more now.
Stations: 538, 1534, 1712, 2034, 2219, 3044
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Fault mode after big electrostatic discharges. ant01n3 1 1,433 2024-01-30, 22:55
Last Post: dupreezd
  fault led at first boot uvash 3 13,142 2021-11-18, 10:37
Last Post: aloha20
  How to get alerts of fault or missing GPS jchonig 2 9,255 2020-12-30, 18:23
Last Post: cutty

Forum Jump:


Users browsing this thread: 1 Guest(s)