Welcome, Guest |
You have to register before you can post on our site.
|
Latest Threads |
Locating ferrite antennas...
Forum: Hardware, Software, Lightning Physics
Last Post: Geewizard
6 hours ago
» Replies: 0
» Views: 35
|
System Blue Basic - Indic...
Forum: General Discussion
Last Post: Geewizard
6 hours ago
» Replies: 14
» Views: 9,419
|
air-core loop connection ...
Forum: Hardware, Software, Lightning Physics
Last Post: GeezerD
Yesterday, 07:09
» Replies: 1
» Views: 750
|
Curious About Setting Up ...
Forum: General Discussion
Last Post: GeezerD
Yesterday, 07:07
» Replies: 2
» Views: 530
|
NEW SYSTEM RED FOR SALE
Forum: General Discussion
Last Post: davidmc36
2025-07-07, 19:41
» Replies: 12
» Views: 7,073
|
Printing 3D casing for Bl...
Forum: General Discussion
Last Post: Tobi
2025-07-05, 15:13
» Replies: 3
» Views: 6,345
|
How to Optimize
Forum: Hardware, Software, Lightning Physics
Last Post: davidmc36
2025-07-04, 15:17
» Replies: 0
» Views: 536
|
System Blue Basic availab...
Forum: General Discussion
Last Post: carseman
2025-07-04, 15:02
» Replies: 19
» Views: 8,860
|
Is there a way to do this...
Forum: General Discussion
Last Post: Eric.Wouters
2025-07-04, 12:17
» Replies: 1
» Views: 434
|
Station Isn't Recognized....
Forum: Website, Maps and Applications
Last Post: davidmc36
2025-07-03, 21:47
» Replies: 220
» Views: 874,005
|
|
|
Electric vs Magnetic antenna |
Posted by: GilbertKE - 2017-12-18, 08:22 - Forum: Hardware, Software, Lightning Physics
- Replies (7)
|
 |
Hello,
Does any one know the range (km) that Electric signal can detect? My guess is that Magnetic antenna (H) detects strikes in longer distances than Electric antenna. I see more detections (signals and effectivity L) with ferrite antennal than E antenna.
I am also thinking of adding a filter to Magnetic channel. Of the 3 H field channels, which would work best?
|
|
|
Setting up an Account for Blitzortung.org |
Posted by: GilbertKE - 2017-12-09, 07:54 - Forum: Website, Maps and Applications
- Replies (4)
|
 |
I just finished soldering system blue in Kenya. Now I want to I want to set up an account with Blitzortung, but I don't I can't locate it. On the manual documentation, it is stated:
"On the web page of the internal web server, you find a link to request an account for Blitzortung.org. Follow the instructions in the email you will receive. The account is associated with your email address.
"
Where is this "Internal web Server"? and how do I get the link?
Thanks,
Gilbert
|
|
|
Link to request account |
Posted by: diaan - 2017-11-30, 17:40 - Forum: General Discussion
- Replies (5)
|
 |
Hi all,
Got my system blue up and running!
I see no "link to request an account for Blitzortung.org."
What am I missing? I have looked everywhere (Except for the right spot, obviously!) but do not see it.
I want to update the firmware since it says "unknown pc board", but cannot download it without an account.
Please assist.
|
|
|
Get no IP - What's wrong? |
Posted by: glump - 2017-11-28, 13:27 - Forum: General Discussion
- Replies (6)
|
 |
Hello community,
I'm new here and got my kit today and soldered right away.
It lacks only the 2 filter IC's because I am not clear in which filter I should solder them.
There are 4 on the circuit board.
Does not it matter?
First everything built into the case and then connected a 5V 2A power supply.
The red power LED lights up and it beeps twice -
then the mode LED flickers very weak and after some time it beeps again.
The LEDs on the network socket light or flicker with the traffic on the network.
Unfortunately, I get from DHCP (SBS Server 2011) obviously no IP address.
Even a test for a new router with DHCP was unsuccessful.
Have again taken the board out of the housing and tested all solder joints - looks good.
Inside, the red LED on the GPS receiver is flashing. There is a new GPS antenna connected.
The 2 crystals are on the correct position.
Does anyone have a tip for me ....
Greetings from Carinthia,
|
|
|
Inbetriebnahme blue |
Posted by: glump - 2017-11-27, 21:25 - Forum: Non-English
- Replies (4)
|
 |
Hallo Gemeinde,
bin neu hier und habe heute meinen Bausatz erhalten und gleich zusammengelötet.
Es fehlen nur die 2 Filter-IC's da mir nicht klar ist bei welchen Filter ich die einlöten soll. Auf der Leiterplatte gibt es ja 4.
Ist das egal ?
Erstmal alles in das Gehäuse eingebaut und dann ein 5V 2A Netzteil drangehängt.
Die rote Power-LED leuchtet und es piept 2x - danach flackert die Mode LED ganz schwach und nach einiger Zeit piept es nochmals.
Die LED's an der Netzwerkbuchse leuchten bzw. flackern mit dem Traffic am Netz.
Nur leider bekomme ich vom DHCP (SBS Server 2011) offensichtlich keine IP Adresse. Auch ein Test auf einen neuen Router mit DHCP ergab keinen Erfolg.
Hab nun nochmals die Platine aus dem Gehäuse genommen und alle Lötstellen geprüft - sieht gut aus.
Innen blink noch die rote LED beim GPS Empfänger. Da ist eine neue GPS Antenne angeschlossen.
Hat da jemand einen Tipp für mich....
Grüße aus Kärnten,
Karl
Sorry für den Doppel-Post E/D - wollte eigentlich den hier löschen finde aber keine Möglichkeit
|
|
|
|